class Sigfox

Sigfox is a Low Power Wide Area Network protocol that enables remote devices to connect using ultra-narrow band, UNB technology. The protocol is bi-directional, messages can both be sent up to and down from the Sigfox servers.

for i in range(1, 100):
  # send something
  s.send('Hello ' + str(i))

This class provides a driver for the Sigfox network processor in the Sigfox enabled Pycom devices.

Quick Usage Example

from network import Sigfox
import socket

# init Sigfox for RCZ1 (Europe)
sigfox = Sigfox(mode=Sigfox.SIGFOX, rcz=Sigfox.RCZ1)

# create a Sigfox socket
s = socket.socket(socket.AF_SIGFOX, socket.SOCK_RAW)

# make the socket blocking
s.setblocking(True)

# configure it as uplink only
s.setsockopt(socket.SOL_SIGFOX, socket.SO_RX, False)

# send some bytes
s.send(bytes([1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12]))

Constructors

class network.Sigfox(id=0, ...)

Create and configure a Sigfox object. See init for params of configuration. Examples:

# configure radio for the Sigfox network, using RCZ1 (868 MHz)
sigfox = Sigfox(mode=Sigfox.SIGFOX, rcz=Sigfox.RCZ1)

# configure radio for FSK, device to device across 912 MHz
sigfox = Sigfox(mode=Sigfox.FSK, frequency=912000000)

Methods

sigfox.init(mode=Sigfox.SIGFOX, rcz=Sigfox.RCZ1, * , frequency=None)

Set the Sigfox radio configuration.

The arguments are:

• mode can be either Sigfox.SIGFOX or Sigfox.FSK. Sigfox.SIGFOX uses the Sigfox modulation and protocol while Sigfox.FSK allows to create point to point communication between 2 Devices using FSK modulation. Note: Sigfox.FSK mode is not supported on LoPy 4 and FiPy.
• rcz takes the following values: Sigfox.RCZ1, Sigfox.RCZ2, Sigfox.RCZ3, Sigfox.RCZ4. The rcz argument is only required if the mode is Sigfox.SIGFOX.
• frequency sets the frequency value in FSK mode. Can take values between 863 and 928 MHz.

sigfox.mac()

Returns a byte object with the 8-Byte MAC address of the Sigfox radio.

sigfox.id()

Returns a byte object with the 4-Byte bytes object with the Sigfox ID.

sigfox.rssi()

Returns a signed integer with indicating the signal strength value of the last received packet.

sigfox.pac()

Returns a byte object with the 8-Byte bytes object with the Sigfox PAC.

print(ubinascii.hexlify(sigfox.mac()))

sigfox.frequencies()

Returns a tuple of the form: (uplink_frequency_hz, downlink_frequency_hz)

sigfox.public_key([public])

Sets or gets the public key flag. When called passing a True value the Sigfox public key will be used to encrypt the packets. Calling it without arguments returns the state of the flag.

# enable encrypted packets
sigfox.public_key(True)

# return state of public_key
sigfox.public_key()

Constants

sigfox.SIGFOX sigfox.FSK Sigfox radio mode. SIGFOX to specify usage of the Sigfox Public Network. FSK to specify device to device communication.

sigfox.RCZ1 sigfox.RCZ2 sigfox.RCZ3 sigfox.RCZ4 Sigfox zones.

• RCZ1 to specify Europe, Oman & South Africa.
• RCZ2 for the USA, Mexico & Brazil. RCZ3 for Japan.
• RCZ4 for Australia, New Zealand, Singapore, Taiwan, Hong Kong, Colombia & Argentina.

Working with Sigfox Sockets

Sigfox sockets are created in the following way:

import socket
s = socket.socket(socket.AF_SIGFOX, socket.SOCK_RAW)

And they must be created after initialising the Sigfox network card.

Sigfox sockets support the following standard methods from the socket module:

socket.close()

Use it to close an existing socket.

socket.send(bytes)

In Sigfox mode the maximum data size is 12 bytes. In FSK the maximum is 64.

# send a Sigfox payload of bytes
s.send(bytes([1, 2, 3]))

# send a Sigfox payload containing a string
s.send('Hello')

socket.recv(bufsize)

This method can be used to receive a Sigfox downlink or FSK message.

# size of buffer should be passed for expected payload, e.g. 64 bytes
s.recv(64)

socket.setsockopt(level, optname, value)

Set the value of the given socket option. The needed symbolic constants are defined in the socket module (SO_* etc.). In the case of Sigfox the values are always an integer. Examples:

# wait for a downlink after sending the uplink packet
s.setsockopt(socket.SOL_SIGFOX, socket.SO_RX, True)

# make the socket uplink only
s.setsockopt(socket.SOL_SIGFOX, socket.SO_RX, False)

# use the socket to send a Sigfox Out Of Band message
s.setsockopt(socket.SOL_SIGFOX, socket.SO_OOB, True)

# disable Out-Of-Band to use the socket normally
s.setsockopt(socket.SOL_SIGFOX, socket.SO_OOB, False)

# select the bit value when sending bit only packets
s.setsockopt(socket.SOL_SIGFOX, socket.SO_BIT, False)

Sending a Sigfox packet with a single bit is achieved by sending an empty string, i.e.:

import socket
s = socket.socket(socket.AF_SIGFOX, socket.SOCK_RAW)

# send a 1 bit
s.setsockopt(socket.SOL_SIGFOX, socket.SO_BIT, True)
s.send('')
socket.settimeout(value)
# set timeout for the socket, e.g. 5 seconds
s.settimeout(5.0)
socket.setblocking(flag)
# specifies if socket should be blocking based upon Boolean flag.
s.setblocking(True)

If the socket is set to blocking, your code will be wait until the socket completes sending/receiving.

Sigfox Downlink

A Sigfox capable Pycom devices (SiPy) can both send and receive data from the Sigfox network. To receive data, a message must first be sent up to Sigfox, requesting a downlink message. This can be done by passing a True argument into the setsockopt() method.

s.setsockopt(socket.SOL_SIGFOX, socket.SO_RX, True)

An example of the downlink procedure can be seen below:

# init Sigfox for RCZ1 (Europe)
sigfox = Sigfox(mode=Sigfox.SIGFOX, rcz=Sigfox.RCZ1)

# create a Sigfox socket
s = socket.socket(socket.AF_SIGFOX, socket.SOCK_RAW)

# make the socket blocking
s.setblocking(True)

# configure it as DOWNLINK specified by 'True'
s.setsockopt(socket.SOL_SIGFOX, socket.SO_RX, True)

# send some bytes and request DOWNLINK
s.send(bytes([1, 2, 3]))

# await DOWNLINK message
s.recv(32)

Sigfox FSK (Device to Device)

To communicate between two Sigfox capable devices, it may be used in FSK mode. Two devices are required to be set to the same frequency, both using FSK.

Device 1:

sigfox = Sigfox(mode=Sigfox.FSK, frequency=868000000)

s = socket.socket(socket.AF_SIGFOX, socket.SOCK_RAW)
s.setblocking(True)

while True:
  s.send('Device-1')
  time.sleep(1)
  print(s.recv(64))

Device 2:

sigfox = Sigfox(mode=Sigfox.FSK, frequency=868000000)

s = socket.socket(socket.AF_SIGFOX, socket.SOCK_RAW)
s.setblocking(True)

while True:
  s.send('Device-2')
  time.sleep(1)
  print(s.recv(64))